How To Install Vinyl Fencing Posts

Interested in installing your own UltraGuard vinyl fencing? We offering a diversity of tips and tricks too as full, downloadable installation guides. Click on the link to download instructions on how to install UltraGuard semi-privacy fences. Getting most types of UltraGuard fences installed will follow a like process, though most fencing materials will come with a custom installation manual.

Proceed in listen: These installation guidelines should prove successful in weather where winds are low-cal to moderate and soil conditions are stable. In weather where wind loads are loftier or soil is less stable, other practices may exist desired such as: Using larger holes for posts, installing rebar in each mail, and filling the inside with physical to approximately i′ to 2′ above course.

Installing UltraGuard Fence Posts

Step 1: Survey the land for special features, obstructions, underground cables, and concrete from one-time argue. Be sure to follow all local building codes and obtain a building permit if necessary. If underground utility lines are present, contact your utility companies before digging.

Pace 2: Run string lines – push equally low to the ground as possible without distorting a direct line. (Avert tall grass, weeds)

Stride 3: Map location for holes – using 50′ or 100′ record measure, run along string line and spray with marking paint every 6′-0″ or 8′-0″ (the length of your fence sections). (Call up that posts should non be installed more than 8′ center to center, but may exist slightly under as rails may be cutting, but not diffuse.) Employ a different mark to signify location of gate posts. (See Diagram 1)

Step iv: Dig post holes – remove cord line without moving stakes. Using a post pigsty digger or auger chip (8″ for 4″ posts, 10″ for five″ posts) dig down to proper depth while staying every bit plumb as possible. Echo for every 6′ or 8′  mark as well equally gate openings. Accuracy in depth helps to simplify installation.

Notation: Recommended depth of holes to be iii′-0″ minimum- bank check local codes and frostline as greater depths may be required.

Step 5: Re-run string line on original stakes (8″ to 12″ from high spot of basis.)

Step half-dozen: Set proper postal service in each hole (end, corner, line). Cleanup of some holes may exist necessary due to large rocks or roots. Some posts may need to exist cut. Use a level and hold the post in its desired location. (Bank check height, distance from the side by side post, distance from cord line, and plumb). Postal service should be kept at a slight distance from the string line then as not to deflect line. Use spacing jig as described in the full installation manual to aid in postal service spacing. Repeat until all posts are lightly fix (all the same adjustable).

Pace seven: To ensure a quality job, it is strongly recommended that all line posts be set up in physical. It is necessary to secure all corner, gate, and end posts in concrete. To exercise this, hold the post in place to preclude slippage. Fill remainder of hole around post with concrete to 3-4 inches below basis level. Be certain to work concrete into hole by shaking post. Make certain mail service is exactly where information technology should be. Continue filling all holes. Gate posts must be accurately measured and ready. Make any terminal adjustments and cover concrete with remaining dirt. (See Diagram 2)

Note: It is recommended that concrete foundations exist immune to prepare at least 24 hours earlier continuing to Step 8.

Note: To prevent upwards-heaving posts, either apply a coarse file to roughen upwards the post or drill 3/4″ hole on each side of the postal service near the bottom.

Step 8: Cry holes should be drilled in bottom of lower track, especially if posts are filled with concrete. Using a i/4″ drill bit that is four″ long (from drill chuck), drill three holes- one in heart and the other 2 at each cease of rail, approximately viii to 12 inches from the cease. Holes should be drilled from bottom and through both internal ribs in the rail. (See Diagram 3.) This will prevent wet from collecting in the rail and increase the longevity of your fence.

Step 9: Install pre-assembled debate sections. Starting from one cease, insert the lesser track into the start postal service, then follow with the mid and top rails. Push the runway into the routed hols until the notch engages properly. Moving to the complimentary end of the vinyl fencing section, stop installing the department into the 2nd mail service. Insert the bottom rail offset past firmly pushing the rails into the start post and so swing the free end upwards over the lesser pigsty in the 2d post. Push button the rail down until it snaps into the lower hole. Complete the installation past inserting mid and superlative rails.

Footstep 10: Continue installing sections equally indicated in Pace 9 until all sections are secured in the posts.

Step 11: Install alignment screws on the within of each section as show in Diagram 5. Keep the border of alignment cap as tight to post every bit possible and position about 1 3/iv″ from edge of rail. See Diagram 6 for recommended location of screws. (Self-drilling screws are provided- a power screw driver or drill should provide easiest installation.)

Step 12: Clean upward fence and put caps on all posts. Have care in wiping downwards the entire contend, peculiarly any concrete which may exist on the posts or the ground.

Note: To ensure proper post spacing, make a jig from scrap fence rails or a forest two x 4 measuring the post-obit length:

Cutting Semi-Privacy Sections

Footstep one: Using a tape measure, observe "A" (the measurement of the center of 1 postal service to the center of the next mail service) and write down the number.

Step 2: Locate the center point of the department and mark it with a pencil or piece of chalk as testify. For six′ fence sections, you desire roughly 35 seven/viii″. For 8′ sections, you want roughly 47 7/viii″.

Step iii: Using 1/2 of the measurement of "A" from Step 1, measure out from the eye mark on the rails and marking as shown below. Cut the rails and remove whatever pickets which are within ii 1/ii″ from the ends of the rails. (Note: Pickets are notched on the bottom and must be compressed with a clamp only in a higher place the notch to remove.)

Pace 4: Afterward unnecessary pickets accept been removed, notch the rails and the section volition be set up to install.

Source: https://installvinylfencing.com/vinyl-fence-brands/how-to-install-ultraguard-vinyl-fence/

Posted by: smiththavis.blogspot.com

Share this post